NOVEMBER 2013
Dear Subscriber
Please take note of the following amendments which have been made to our COMPULSORY Standards issued by our Department Of Trade And
Industry over OCTOBER – NOVEMBER 2013
Alison Lee
STANDARDS
No. 782 18 October 2013 (Government Gazette 36923)
STANDARDS ACT, 2008
STANDARDS MATTERS
In terms of the Standards Act, 2008 (Act No. 8 of 2008), the Council of the South African Bureau of Standards has acted in regard to standards in
the manner set out in the Schedules to this notice.
All South African standards that were previously published by the South African Bureau of Standards with the prefix "SABS" have been redesignated
as South African national standards and are now published by the SABS Standards Division (a division of SABS) with the prefix "SANS".
A list of all existing South African national standards was published by Government Notice No. 1373 of 8 November 2002.
In the list of SANS standards below, the equivalent SABS numbers, where applicable, are given below the new SANS numbers for the sake of
convenience. Standards that were published with the "SABS" prefix are listed as such.
SCHEDULE 1: ISSUE OF NEW STANDARDS
The standards mentioned have been issued in terms of section 16(3) of the Act.
Standard No.
and year
SANS 689:2013
SANS
3457:2013/ ISO
3457:2003
SANS 43784:2013/ ISO
4378-4:2009
SANS 117705:2013/ ISO/IEC
11770-5:2011
SANS 126511:2013/ ISO
12651-1
SANS
13766:2013/ ISO
13766:2006
SANS 204923:2013/ ISO
20492-3:2010
SANS 204924:2013/ ISO
20492-4:2010
SANS
24745:2013/
ISO/IEC
24745:2011
SANS
27007:2013/
ISO/IEC
27007:2011
SANS
27010:2013/
ISO/IEC
27010:2012
Title, scope and purport
Automatic rail-weighbridges. Specifies requirements and test methods for automatic
rail-weighbridges (ARWs) used to determine the mass of railway wagons when they are
in motion, as well as requirements for integral control instruments for the partial static
weighing of reference wagons. Also provides standardized requirements and testing
procedures to evaluate the metrological and technical characteristics of an ARW in a
uniform and traceable way.
Earth-moving machinery - Guards - Definitions and ISO requirements. Defines principal
terms and specifies requirements for, and characteristics of, guards and other means of
protecting personnel from mechanical, fluid or thermal hazards associated with the
operation and routine maintenance of earthmoving machinery as defined in ISO 6165
(published in South Africa as an identical adoption under the designation SANS 261),
when used as intended by the manufacturer.
Plain bearings - Terms, definitions, classification and symbols - Part 4: Basic
symbols. Defines basic symbols for use in the field of plain bearings. Additional signs
are also defined for use as superscripts and subscripts. This classification is
established for use in calculations and technological and geometrical determinations,
as well as in the quality assurance of plain bearings.
Information technology - Security techniques - Key management - Part 5: Group key
management. Specifies key establishment mechanisms for multiple entities to provide
procedures for handling cryptographic keying material used in symmetric or asymmetric
cryptographic algorithms in accordance with the security policy in force.
Electronic document management - Vocabulary - Part I: Electronic document
imaging. Facilitate communication in the field of electronic document management and
translation of the terms it contains into other languages.
Earth-moving machinery - Electromagnetic compatibility. Provides test methods and
acceptance criteria for the evaluation of the electromagnetic compatibility of earthmoving machinery as defined in ISO 6165 (published in South Africa as an identical
adoption under the designation SANS 261).
Glass in buildings - Insulating glass units - Part 3: Gas concentration and gas
leakage. Specifies two methods of test for insulating glass units, including a
determination of the gas leakage rate and a determination of gas concentration
tolerances. The two methods designated as approach 1, which is intended for use in
markets such as North America, and approach 2, which is intended for use in markets
such as Europe.
Glass in buildings - Insulating glass units - Part 4: Method of test for the physical
attribute of edge seals. Specifies methods for testing the edge seal strength, and
partially testing the moisture and gas permeation through sealants, of glass insulating
units.
Information technology - Security techniques - Biometric information
protection. Provides guidance for the protection of biometric information under various
requirements for confidentiality, integrity and renewability/revocability during storage
and transfer. Also provides requirements and guidelines for the secure and privacycompliant management and processing of biometric information.
Information technology - Security techniques - Guidelines for information security
management systems auditing. Provides guidance on managing an information security
management system (ISMS) audit programme, on conducting the audits, and on the
competence of ISMS auditors.
Information technology - Security techniques - Information security management for
inter-sector and inter- organizational communications. Provides guidelines in addition to
guidance given in the ISO/IEC 27000 family of standards for implementing information
security management within information sharing communities. Provides controls and
guidance specifically relating to initiating, implementing, maintaining, and improving
information security in inter-organization and inter-sector communications.
SANS 270341:2013/
ISO/IEC 270341:2011
SANS
27035:2013/
ISO/IEC
27035:2011
SANS 285601:2013/
ISO 285601:2011
SANS 285603:2013/
ISO 285603:2011
SANS
29128:2013/
ISO/IEC
29128:2011
SANS
29150:2013/
ISO/IEC
29150:2011
SANS 291922:2013/
ISO/IEC 291922:2011
SANS
30300:2013/
ISO 30300:2011
SANS
30301:2013/
ISO 30301:2011
SANS 6007933:2013/ IEC
60079-33:2012
SANS 6196811:2013/ IEC
61968-11:2013
SANS 62271-37082:2013/
IEC/IEEE 6227137-082:2012
Information technology - Security techniques - Application security - Part 1: Overview
and concepts. Provides
guidance to assist organizations in integrating security into the processes used for
managing their applications. Presents an overview of application security.
Information technology - Security techniques - Information security incident
management. Provides a structured and
planned approach to detect, report and assess information security incidents, respond
to and manage information security incidents, detect, assess and manage information
security vulnerabilities, and continuously improve information security and incident
management as a result of managing information security incidents and vulnerabilities.
Information and documentation - RFID in libraries - Part 1: Data elements and general
guidelines for implementation.
Specifies a model for the use of radio frequency identification (RFID) tags for items
appropriate for the needs of all types of libraries, including academic, public, corporate,
special and school.
Information and documentation - RFID in libraries - Part 3: Fixed length
encoding. Provides a data model and
encoding rules for the use of radio frequency identification (RFID) tags for items
appropriate for the needs of all types of libraries (including academic, public, corporate,
special and school libraries). Specifies the rules for encoding a subset of data elements
taken from the total set of data elements listed in ISO 28560-1 (published in South
Africa as an identical adoption under the designation SANS 28560-1) into a basic block
and other data elements into extension blocks onto the RFID tag.
Information technology - Security techniques - Verification of cryptographic
protocols. Establishes a technical base for
the security proof of the specification of cryptographic protocols. Specifies design
evaluation criteria for these protocols, as well as methods to be applied in a verification
process for such protocols.
Information technology - Security techniques - Signcryption. Specifies four mechanisms
for signcryption that employ
public key cryptographic techniques requiring both the originator and the recipient of
protected data to have their own public and private key pairs.
Information technology - Security techniques - Lightweight crytography - Part 2: Block
ciphers. Specifies two block
ciphers suitable for applications that require lightweight cryptographic implementations,
namely PRESENT: a lightweight block cipher with a block size of 64 bits and a key size
of 80 or 128 bits, and CLEFIA: a lightweight block cipher with a block size of 128 bits
and a key size of 128, 192 or 256 bits.
Information and documentation - Management systems for records - Fundamentals and
vocabulary. Defines terms and
definitions applicable to the standards on MSR prepared by ISO/TC 46/SC 11.
Establishes the objectives for using a MSR, provides principles for a MSR, describes a
process approach and specifies roles for top management.
Information and documentation - Management systems for records Requirements. Specifies requirements to be met
by a MSR in order to support an organization in the achievement of its mandate,
mission, strategy and goals. It addresses the development and implementation of a
records policy and objectives and gives information on measuring and monitoring
performance.
Explosive atmospheres - Part 33: Equipment protection by special protection "s". Gives
the specific methodology for the assessment and testing, and requirements for marking
of electrical equipment, parts of electrical equipment and Ex components with special
protection "s".
Application integration at electric utilities - System interfaces for distribution
management - Part 11: Common information model (CIM) extensions for
distribution. Specifies the distribution extensions of the Common Information Model
(CIM). Covers the information model that extends the base CIM for the needs of
distribution networks, as well as for integration with enterprise-wide information systems
typically used within electrical utilities.
High-voltage switchgear and controlgear - Part 37-082: Standard practice for the
measurement of sound pressure
levels on alternating current circuit-breakers. Provides methods for the measurement of
sound pressure levels produced by outdoor alternating current circuit-breakers in a
free-field environment.
Self-ballasted LED-lamps for general lighting services by voltage > 50 V - Safety
specification. Specifies the safety and interchangeability requirements, together with the
SANS
test methods and conditions required to show compliance of LED-lamps with integrated
62560:2013/ IEC
means for stable operation (self-ballasted LED-lamps), intended for domestic and
62560:2011
similar general lighting purposes, having a rated wattage up to 60 W, a rated voltage of
> 50 V up to 250 V and caps as specified.
Explosive atmospheres - Part 34: Application of quality systems for equipment
manufacture. Specifies particular requirements and information for establishing and
SANS 80079- maintaining a quality system to manufacture Ex equipment including protective systems
34:2013/ IEC in accordance with the Ex certificate. It does not preclude the use of other quality
80079-34:2011 systems that are compatible with the objectives of ISO 9001 (published in South Africa
as an identical adoption under the designation SANS 9001) and provide equivalent
results.
SATS
General lighting - LEDs and LED modules - Terms and definitions.Presents terms and
62504:2013/
definitions relevant for lighting
IEC/TS
with LED light sources.
62504:2011
SCHEDULE 2: AMENDMENT OF EXISTING STANDARDS
The standards mentioned have been amended in terms of section 16(3) of the Act. The number and date of a standard that has been superseded
appear in brackets below the new number. In the case of an amendment issued in consolidated format, the edition number of the new (consolidated)
edition appears in brackets below the number of the standard.
Standard No. and
Title, scope and purport
year
SANS 193:2013 (Ed. Fire dampers. Consolidated edition incorporating amendment No. 2.Amended to
2.2)
update referenced standards.
Earth-moving machinery - Basic types - Identification and terms and
definitions. Gives terms and definitions and an identification structure for classifying
SANS 261:2013/ earth-moving machinery designed to perform excavation, loading, transportation,
ISO 6165:2012
and drilling, spreading, compacting or trenching of earth, rock, and other materials,
(SANS 261:2008) during work, for example, on roads and dams, in quarries and mines, and on
building sites. Purpose is to provide a clear means of identifying machines
according to their function and design configurations.
Wooden poles, droppers, guardrail posts and spacer blocks - Part 3: Hardwood
species. This part of SANS 457 specifies requirements for preservative-treated
hardwood structural poles, agricultural poles, fencing poles, round droppers,
SANS 457-3:2013
guardrail posts and spacer blocks. The poles are intended for the erection of fences
(SABS 457-3:2000)
and vine trellises, for general use in orchards and for structural purposes. The
droppers are intended for fencing. The posts and spacer blocks are intended for the
erection of steel guardrails at the sides of roads.
Luminaires for interior lighting, streetlighting and floodlighting - Performance
SANS 475:2013 (Ed. requirements. Consolidated edition incorporating amendment No. 2. Amended to
1.2)
update referenced standards and to correct the power factor for lamps smaller than
or equal to 25 Watts.
Light steel frame building. Consolidated edition incorporating amendment No.
2. Amended to update referenced standards, to correct the map on geographic
SANS 517:2013 (Ed. regions related to wind speeds, to update requirements in the tables on external
1.2)
pressure coefficient cpe for mono-pitched roofs and duo-pitched roofs, to update
requirements for wall elements, and to correct the map on climate zones in South
Africa.
Mixtures of copper-chromium-arsenic compounds for timber preservation.
Consolidated edition incorporating amendment No. 3.Amended to include the X-ray
SANS 673:2013 (Ed. fluorescence (XRF) and the inductively coupled plasma emission (ICP)
3.3)
spectrometric methods of analyses and to renumber accordingly, to amend the
requirements with respect to the gooch crucible that is used in the wet tritation
methods of arsenic content elemental concentration.
Electric cables for motor vehicles - Low-voltage cables and flexible earthing straps
SANS 1017:2013
for motor vehicles. Consolidated edition incorporating amendment No. 5. Amended
(Ed. 1.5)
to update referenced standards.
Aggregates from natural sources - Aggregates for concrete. Consolidated edition
incorporating amendment No. 3. Amended to modify the introduction, update
SANS 1083:2013
referenced standards, to modify the definitions of "aggregate", "coarse aggregate"
(Ed. 2.3)
and "fine aggregate", change the sieve grading sizes and modify the requirements
for coarse aggregate for use in concrete.
Symbolic safety signs - Part 3: Internally illuminated signs. Consolidated edition
SANS 1186-3:2013
incorporating amendment No. 3. Amended to replace reference to SANS 7253 with
(Ed. 1.3)
SANS 9227.
SANS 1236:2013 Silvered glass mirrors for general use. Consolidated edition incorporating
(Ed. 1.2)
amendment No. 2. Amended to update referenced standards.
Safety and security glazing materials for buildings - Part 3: Bullet-resistant glazing
materials. Consolidated edition incorporating amendment No. 3. Amended to
SANS 1263-3:2013/ correct cross-references to referenced standards, to modify the requirements for
(Ed. 1.3)
classification of glazing material, calibre of firearm, ammunition and range in the
table on levels of simulated ballistic attack, and to replace the apparatus "velocity
measurement system" (and its explanatory footnote) with "ballistic chronograph".
SANS 1422:2013 Domestic electric laundry treatment machines. Consolidated edition incorporating
(Ed. 2.1)
amendment No. 1. Amended to move reference to legislation to the foreword.
SANS 1547:2013 Traffic signal controllers. Consolidated edition incorporating amendment No.
(Ed. 1.6)
6. Amended to change electrical requirements for controlgear, and to update
referenced standards.
Pasteurized milk. Consolidated edition incorporating amendment No. 1. Amended
to update legislation and the referenced standards.
D.C. supplied luminaires for fluorescent lamps. Consolidated edition incorporating
SANS 1814:2013
amendment No. 3. Amended to update referenced standards. Can only be used in
(Ed. 1.3)
conjunction with SANS 60925, SANS 60598-1 and SANS 61347-2-3.
Electricity supply - Quality of supply: Power quality monitoring instruments
specification. Specifies product requirements for instruments, the functions of which
include measuring and monitoring of power quality parameters in a.c. power
systems. Can be used in, for example, the generation, transmission and distribution
SANS 1816:2013
of electricity and related telecommunication systems, e.g. inside a power station or
(SANS 1816:2005)
a substation, or a distributed generator connection, or at the interface point between
the installation and the network, e.g. in order to check the compliance to the
connection agreement with a network operator. Can only be used in conjunction
with SANS 61000-4-30.
SANS 1865:2013 Point-of-use drinking water treatment units. Consolidated edition incorporating
(Ed. 1.2)
amendment No. 2. Amended to update a referenced standard.
Available alkali content of cement extenders (complying with SANS 50197-1).
SANS 6152:2013
Consolidated edition incorporating amendment No. 1.Amended to update
(Ed. 2.1)
referenced standards.
SANS 6210:2013 Domestic solar water heaters - Mechanical qualification tests. Consolidated edition
(Ed. 3.1)
incorporating amendment No. 1. Amended to update referenced standards.
Water quality - Determination of chloride - Silver nitrate titration with chromate
SANS 9297:2013
indicator (Mohr's method). Consolidated edition incorporating amendment No.
(Ed. 1.2)
2. Amended to update referenced standards.
The measurement and assessment of occupational noise for hearing conservation
SANS 10083:2013 purposes. Consolidated edition incorporating amendment No. 2. Amended to
(Ed. 5.2)
change requirements for baseline audiometry, and to change the title and text of the
table on frequency of contributions to the PLH (table 1).
SANS 10204:2013 The application of fumigants. Consolidated edition incorporating amendment No.
(Ed. 2.2)
2. Amended to move a reference to legislation to the foreword.
Earthing of low-voltage (LV) distribution systems. Gives requirements and
recommendations for the provision of a safe electricity supply to the consumer.
SANS 10292:2013 Establishes general principles for the earthing of low-voltage distribution systems of
(SABS 0292:2001) which the supply starts at the point of generation or transformation and ends at the
supply earth terminal of the consumer. Applies to a distributor that operates at a
voltage (a.c. or d.c.) that does not exceed 1 000 V.
Building construction - Sealants - Determination of tensile properties of sealants at
SANS 10590:2013/
maintained extension after immersion in water.Specifies a method for the
ISO 10590:2005
determination of the influence of water immersion on the adhesion/cohesion
(SABS ISO
properties at maintained extension of sealants used in joints in building
10590:1991)
construction.
Document management - Information stored electronically - Recommendations for
SANS 15801:2013/
trustworthiness and reliability.
Describes the implementation and operation of document management systems
ISO/TR 15801:2009
that can be considered to store electronic information in a trustworthy and reliable
(SANS 15801:2005)
manner.
Information technology - Radio frequency identification for item management - Part
SANS 180003: Parameters for air interface communications at 13,56 MHz. Provides physical
3:2013/ ISO/IEC
layer, collision management system and protocol values for RFID systems for item
18000-3:2010
identification operating at 13,56 MHz in accordance with the requirements of
(SANS 18000ISO/IEC 18000-1 (published in South Africa as an identical adoption under the
3:2009)
designation SANS 18000-1).
SANS 18000Information technology - Radio frequency identification for item management - Part
6:2013/ ISO/IEC
6: Parameters for air interface communications at 860 MHz to 960 MHz
18000-6:2013
General. Defines the air interface for radio frequency identification (RFID) devices
(SANS 18000operating in the 860 MHz to 960 MHz industrial, scientific, and medical (ISM) band
6:2012)
used in item management applications.
Geographic information - Methodology for feature cataloguing. ISO amendment No.
1. Amended to change the scope and the clause on conformance, to update
SANS 19110:2005/
referenced standards and terms and definitions, to change the clauses on
ISO 19110:2005
abbreviations and principal requirements and the annexes on abstract test suite,
feature catalogue template, feature cataloguing examples, and feature cataloguing
SANS 1679:2013
(Ed. 2.1)
SANS 19131:2012/
ISO 19131:2007
SANS 20011:1981/
ECE R11:1981
SANS 20014:2006/
ECE R14:2006
SANS 20017:2004/
ECE R17:2002
SANS 60311:2013/
IEC 60311:2009
(Ed. 3.2)
SANS 60335-227:2013/ IEC 603352-27:2012 (Ed. 4.1)
SANS 604321:2013/ IEC 60432-
concepts, and to insert three new annexes on encoding description, management
of feature catalogue registers, and XML implementation example.
Geographic information - Data product specifications. ISO amendment No.
1. Amended to include requirements relating to the inclusion of an application
schema and feature catalogue and the treatment of coverages in an application
schema.
Uniform provisions concerning the approval of vehicles with regard to door latches
and door retention components. ECE amendment No. 2.Amended to change the
scope, to add definitions, to change the clauses on approval, specifications, tests
and modification of the vehicle type, to insert a new clause on transitional provision,
to change the annexes on arrangements of approval marks, latch test for load tests
one, two, and three and force application, to add a new clause on inertial test
procedures, hinge test procedure and sliding side door. ECE amendment No.
3. Amended to change requirements for tests on load test three, door hinges, door
system, and door locks, to change requirements for test in the annexes on test
procedure for door latches and door retention components, inertial test procedures,
hinge test procedure, and sliding side door. ECE amendment No. 4.Amended to
change requirements for tests on load test three, door hinges, and door system, to
change requirements for tests in the annexes on test procedure for door latches
and door retention components, inertial test procedures, hinge test procedure, and
sliding side door.
Uniform provisions concerning the approval of vehicles with regard to safety-belt
anchorages, isofix anchorages systems and isofix top tether anchorages. ECE
amendment No. 3. Amended to change the scope. ECE amendment No.
4. Amended to delete a definition, to change requirements for approval, and
specifications, to add requirements in the clause on transitional provisions, and to
change requirements in the annex on arrangements of the approval mark.ECE
amendment No. 5. Amended to change a clause on the minimum number of belt
anchorages to be provided, and to change the requirements of vehicle in categories
M, N, and M1 in the subclause on minimum number of belt anchorages to be
provided. ECE amendment No. 6. Amended to change the design of the ISOFIX
anchorages in the subclause on general specifications. ECE corrigendum No.
2. Corrected to change a definition, and to change the requirements of ISOFIX
anchorages in the subclause on general specifications.
Uniform provisions concerning the approval of vehicles with regard to the seats,
their anchorages and any head restraints. ECE amendment No. 1. Amended to
change the scope, to change the clause on requirement and tests, to add a new
clause in the annex on communication, to correct the word "decelerometers" to read
"accelerometers" in the annex on results, to change the requirements for test in the
annexes on test of resistance to inertia effects, and dynamic testing of seat-backs
and partitioning systems used as luggage restraint systems, and to change the
heading of the graph in the annex on corridor of sled's deceleration or acceleration
as a function of time. ECE amendment No. 2. Amended to change the scope, to
add new definitions, to change a subclause in the clause on approval, to add new
clauses on requirements, to change subclauses in the clause on requirements, to
add new clauses on transitional provisions, and to change the annex on
arrangement of approval marks. ECE amendment No. 3. Amended to change a
definition, and to change and to delete subclauses in the clause on requirements.
Electric irons for household or similar use - Methods for measuring performance.
Consolidated edition incorporating amendment No. 2.Amended to update the
definition of the auto switch-off device, to update the measurement of heating-up
time for steaming operation, the measurement of steaming time, steaming rate and
water leakage rate, the determination of total steaming time for hard water, and
figure 4 (test apparatus).
Household and similar electrical appliances - Safety - Part 2-27: Particular
requirements for appliances for skin exposure to ultraviolet and infrared radiation.
Consolidated edition incorporating amendment No. 1. Amended to change the
heading of the definitions clause to read "Terms and definitions", to give clarification
of radiation measurement procedure and guidelines for an exposure time schedule,
to include a normative annex on software evaluation, and to delete a referenced
standard from the bibliography. Can only be used in conjunction with SANS 603351.
Incandescent lamps - Safety specifications - Part 1: Tungsten filament lamps for
domestic and similar general lighting purposes. Consolidated edition incorporating
1:2012 (Ed. 1.2)
amendment No. 2. Amended to include requirements for K.6 protection from water
contact and K.7 photobiological safety.
Single-capped fluorescent lamps - Performance specifications. IEC amendment No.
SANS 60901:2008/ 5. Amended to replace data sheets, and to update the annexes on method of test
IEC 60901:2008
for electrical, photometric and cathode characteristics, method of test for lumen
maintenance and life, and information for ballast and starter design.
Lamp controlgear - Part 1: General and safety requirements. Consolidated edition
incorporating amendment No. 2. Amended to add an introduction (to amendment
2), to update the scope, normative references, terms and definitions, general
requirements, notes on tests, marking, earthing, protection against accidental
contact with live parts, moisture resistance and insulation, electric strength, thermal
endurance test for windings of ballasts, fault conditions, construction, creepage
SANS 61347distances and clearances, no-load output voltage, to update an annex for test to
1:2013/ IEC 61347- establish whether a conductive part is a live part which may cause an electric shock
1:2012 (Ed. 2.2)
and an annex for thermally protected lamp controlgear, to include an annex for
particular additional requirements for controlgears providing SELV, an annex for
dielectric strength test voltages for controlgear intended for the use in impulse
withstand category III, an annex for requirements for insulation materials used for
double or reinforced insulation, an annex for additional requirements for built-in
electronic controlgear with double or reinforced insulation, and to update the
bibliography.
Lamp controlgear - Part 2-9: Particular requirements for electromagnetic
SANS 61347-2controlgear for discharge lamps (excluding fluorescent lamps). Specifies particular
9:2013/ IEC 61347safety requirements for electromagnetic controlgear for discharge lamps such as
2-9:2012 (SANS
high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium
61347-2-9:2010)
vapour and metal halide lamps.
Discharge lamps (excluding fluorescent lamps) - Safety specifications. Consolidated
edition incorporating amendment No. 2.Amended to add a new paragraph and a
SANS 62035:2013/
NOTE on UV radiation, change a requirement for test procedures and conditions of
IEC 62035:2012
compliance for containment, and include annex I (containment testing procedure for
(Ed. 1.2)
metal halide lamps with quartz arc tubes) and annex J (containment testing
procedure for metal halide lamps with ceramic arc tubes).
SCHEDULE 3: CANCELLATION OF STANDARDS
In terms of section 16(3) of the Act the following standards have been cancelled.
Standard No. and
year
Title
SANS 1561-1:2006
Rewound and refurbished rotating electrical machines - Part 1: Low-voltage threephase induction motors.
SCHEDULE 4: ADDRESSES OF SABS OFFICES
The addresses of offices of the South African Bureau of Standards where copies of standards mentioned in this notice can be obtained, are as
follows:
1. The CEO, South African Bureau of Standards, 1 Dr Lategan Road, Groenkloof, Private Bag X191, Pretoria 0001.
2. The Manager, Western Cape Regional Office, SABS, Liesbeek Park Way, Rosebank, PO Box 615, Rondebosch 7701.
3. The Manager, Eastern Cape Regional Office, SABS, 30 Kipling Road, cor. Diaz and Kipling Roads, Port Elizabeth, PO Box 3013, North End
6056.
4. The Manager, KwaZulu-Natal Regional Office, SABS, 15 Garth Road, Waterval Park, Durban, PO Box 30087, Mayville 4058.
5. The Control Officer, Bloemfontein Branch Office, SABS, 34 Victoria Road, Willows, Bloemfontein, PO Box 20265, Willows 9320.