®
®
Square D Clipsal
Color Touch Screen
SLC50x0CTC Series
Instruction Bulletin
Retain for future use.
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
HAZARD CATEGORIES AND SPECIAL SYMBOLS
Read these instructions carefully and look at the equipment to become
familiar with the device before trying to install, operate, service, or maintain
it. The following special messages may appear throughout this bulletin or on
the equipment to warn of potential hazards or to call attention to information
that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label
indicates that an electrical hazard exists which will result in personal injury if
the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
Danger indicates an immediately hazardous situation which, if not
avoided, will result in death or serious injury.
Warning indicates a potentially hazardous situation which, if not
avoided, can result in death or serious injury.
Caution indicates a potentially hazardous situation which, if not
avoided, can result in minor or moderate injury.
Caution, used without the safety alert symbol, indicates a potentially
hazardous situation which, if not avoided, can result in property
damage or improper operation.
NOTE: Provides additional information to clarify or simplify a procedure.
2
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained
only by qualified personnel. This document is not intended as an instruction
manual for untrained persons. No responsibility is assumed by Square D for
any consequences arising out of the use of this manual.
Class B FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
x
Reorient or relocate the receiving antenna.
x
Increase the separation between the equipment and receiver.
x
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
x
Consult the dealer or an experienced radio/TV technician for help.
© 2007 Schneider Electric. All Rights Reserved.
3
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
TABLE OF CONTENTS
HAZARD CATEGORIES AND SPECIAL SYMBOLS.....................................................................2
PLEASE NOTE................................................................................................................................3
Class B FCC Statement..................................................................................3
TABLE OF CONTENTS ..................................................................................................................4
LIST OF FIGURES ..........................................................................................................................5
LIST OF TABLES ............................................................................................................................6
INTRODUCTION .............................................................................................................................7
INTRODUCTION .............................................................................................................................7
Confirming the Package Contents ..................................................................8
C-Bus System Clock Status..........................................................................10
Megger Testing Information ..........................................................................10
Network Considerations................................................................................10
Selecting a Location......................................................................................11
Infrared Remote Control ...............................................................................12
Installing the Color Touch Screen with IR Support ............................12
SAFETY PRECAUTIONS..............................................................................................................13
INSTALLATION.............................................................................................................................14
Options for Mounting the Color Touch Screen..............................................14
Mounting the Power Supply ..........................................................................15
Mounting the Color Touch Screen ................................................................16
Attaching and Removing the Touch Screen Cover Plate .............................17
CONNECTIONS TO THE COLOR TOUCH SCREEN ..................................................................19
Connecting the Color Touch Screen to the C-Bus Network..........................21
Connecting Serial Communications to the Touch Screen ............................23
Connecting through the Ethernet or RJ45 ....................................................24
Connecting Devices through the PS/2 Connection.......................................25
Caring for the Color Touch Screen ...............................................................25
Connecting the Audio and Infrared ...............................................................26
Connecting the Video....................................................................................26
PROGRAMMING THE COLOR TOUCH SCREEN.......................................................................27
Transferring the Customized Software Project to the Color Touch Screen ..27
Before You Begin and Starting the PICED Software .........................28
Selecting the Project to Transfer........................................................30
Saving the Project onto the Touch Screen ........................................33
Selecting a Network and an IP Address ............................................38
Selecting a Touch Screen and Uploading the Project .......................41
Project Settings and Preferences ......................................................44
Resetting the Color Touch Screen's Software ..............................................46
SPECIFICATIONS .........................................................................................................................47
STANDARDS ................................................................................................................................51
SUPPORT AND SERVICE ............................................................................................................52
4
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
LIST OF FIGURES
Figure 1: Considering the Viewing Angle during Mounting ...................................... 11
Figure 2: Infrared Reception Zones ......................................................................... 12
Figure 3: Attaching the Cover Plate ......................................................................... 17
Figure 4: Removing the Cover Plate........................................................................ 18
Figure 5: Color Touch Screen Back Side Connectors ............................................. 20
Figure 6: Color Touch Screen Front Side Connector............................................... 20
Figure 7: Wiring Connections Key Diagram............................................................. 22
Figure 8: Configuration Startup Screen ................................................................... 29
Figure 9: Piced Startup Icon .................................................................................... 29
Figure 10: Select Project.......................................................................................... 30
Figure 11: Project Type............................................................................................ 31
Figure 12: Select a C-Bus Project............................................................................ 31
Figure 13: Software Revision History....................................................................... 33
Figure 14: Start Color Transfer Software ................................................................. 34
Figure 15: Transfer to Unit ....................................................................................... 35
Figure 16: Confirm and Save ................................................................................... 35
Figure 17: Save Project File..................................................................................... 36
Figure 18: Save Font ............................................................................................... 36
Figure 19: Save File................................................................................................. 37
Figure 20: Select Network Card............................................................................... 38
Figure 21: Select Touch Screen Network ................................................................ 39
Figure 22: Suggested IP Address ............................................................................ 39
Figure 23: Confirming the New Direct IP Address ................................................... 40
Figure 24: IP Address Information ........................................................................... 40
Figure 25: Unit Selection.......................................................................................... 41
Figure 26: Transfer Utility Information...................................................................... 42
Figure 27: Transfer Page ......................................................................................... 42
Figure 28: Upload Information ................................................................................. 43
Figure 29: Control Page........................................................................................... 44
Figure 30: Rename Confirmation............................................................................. 45
Figure 31: Closing the C-Touch Colour Transfer Utility ........................................... 45
Figure 32: Touch Screen Reset Button.................................................................... 46
Figure 33: Color Touch Screen Physical Dimensions Front View ........................... 49
Figure 34: Color Touch Screen Physical Dimensions Side View............................. 49
© 2007 Schneider Electric. All Rights Reserved.
5
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
LIST OF TABLES
Table 1: Touch Screen Package Contents ...........................................................8
Table 2: Required Accessories .............................................................................9
Table 3: Connection Types for the Color Touch Screen.....................................19
Table 4: RJ45 Pin Connections ..........................................................................22
Table 5: RS-232 Connection...............................................................................23
Table 6: Category 5 Crossover Ethernet Patch Cable Wiring Assignments .......25
Table 7: Display/Viewing Area Specifications.....................................................47
Table 8: Color Touch Screen Voltage, Processor, Capacity and Memory
Specifications ......................................................................................................47
Table 9: C-Bus Specifications.............................................................................48
Table 10: Components and Connectors Specifications ......................................48
Table 11: Operating Ranges...............................................................................48
Table 12: Color Touch Screen Physical Characteristics.....................................48
Table 13: Specifications - Infrared Remote Control ............................................50
Table 14: U.S. and Canadian Product Safety Standards and U.S. FCC
Regulations .........................................................................................................51
6
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
INTRODUCTION
The Color Touch Screen is a wall mounted, 6.4 inch, liquid crystal
display (LCD) screen that provides controlling and monitoring
capabilities of an entire C-Bus™system from one location.
The Touch Screen is configured with PICED™ Configuration
Software to display custom graphics such as sliders, images,
gauges, and clocks with any background or style. These graphics
control specific, custom programmed C-Bus related functions when
pressed. Functions include automatically scheduling events based
on the time of day, week, month, or year with the system-integrated
real time clock, and creating scenes that enable a series of related
events to occur with one touch of a button.
Touch screen functions are performed by pressing the touchsensitive LCD screen, or by using the infrared hand-held remote
control unit. Connections and product features include USB and RS232 serial ports, composite video output, 10/100 ethernet interface,
two C-Bus connections (in parallel), audio line in and line out
connections, and built-in speakers.
© 2007 Schneider Electric. All Rights Reserved.
7
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Confirming the Package Contents
Confirm that all components listed below are included in the
package, and inspect the device to confirm there are no dents or
damage before installing.
Confirm the product catalog number listed below matches the
number on the shipping carton.
Table 1: Touch Screen Package Contents
Component
Description and
Component
Information
Catalog Number
Color Touch Screen
N/A
SLC50X0CTC
Choices for the Color
Touch Screen Cover Plate
Neo Aluminum Cover
SLC5050CTC
Saturn, Cream Glass
SLC5080CTC2CR
Saturn, Black Glass
SLC5080CTC2BK
Saturn, Mocha Glass
SLC5080CTC2BR
Saturn, White Glass
SLC5080CTC2WE
Handheld Infrared Remote
Control
(battery included)
-
Programming Cable
2.2 yard red crossover
network cable
-
RJ45 cable joiner
Ferrite Filters (2)
8
large ferrite filter for audio
connection and smaller
ferrite filter for the video
connection
-
LCD Cleaning Cloth
-
Mounting screws (4)
-
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
The following table identifies products provided by the user that may
be used for installation.
Table 2: Required Accessories
Component
Description
Catalog Number
Color Touch Screen
Power Supply*
This power supply must be
used to exercise the
warranty.
SLC5000CTCPS
Nail Bracket
Option for mounting the
Color Touch Screen.
SLC5000CTCNA
Wall Box
Option for mounting the
Color Touch Screen.
SLC5000CTCWB
Plasterboard Bracket
Option for mounting the
Color Touch Screen.
SLC5000CTCRM
*NOTE: The Color Touch Screen Power Supply is ordered
separately, and not included in the Touch Screen's package
contents.
© 2007 Schneider Electric. All Rights Reserved.
9
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
C-Bus System Clock Status
The Color Touch Screen has a software-selectable C-Bus system
clock with the capability to synchronize data communication on the
C-Bus network. The Touch Screen's system clock is disabled by
default since it is recommended that a maximum of three system
clocks be enabled on a network. Refer to the C-Bus Toolkit software
for additional information, and to enable the Color Touch Screen
system clock.
Megger Testing Information
Megger testing of an electrical installation with connected C-Bus
units will not damage the units. The C-Bus units' electronic
components should be considered when interpreting megger
readings.
Never perform megger testing on the pink C-Bus data cabling or
terminals. This may degrade the performance of the network.
Network Considerations
The Color Touch Screen draws 20 mA from the C-Bus network.
Adequate C-Bus power supply units must be installed to support the
connected devices.
10
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Selecting a Location
Prior to installing the Color Touch Screen, consider these factors to
select the best available location:
x
Provide easy access to the Touch Screen by considering
obstructions such as doors.
x
Place the Touch Screen where infrared signals from a remote
control will not be obstructed.
x
Place Touch Screens where a single remote control cannot
access multiple Touch Screens simultaneously. Refer to the
"Installing the Color Touch Screen with IR Support" section of
this manual.
x
Leave the Touch Screen uncovered.
x
Place the Touch Screen where it is not subjected to water,
humidity, direct sunlight, or heavy dust.
x
Only use the Touch Screen indoors.
x
Only mount the Touch Screen vertically in a landscape
orientation to maximize heat dissipation.
x
Provide the optimal mounting height by considering the viewing
angle. The typical viewing angle is 70º left, right, and down, and
40º up. Refer to the "Considering the Viewing Angle during
Mounting" figure.
Figure 1: Considering the Viewing Angle during Mounting
KEY:
A. 70° left
B. 40° up
C. 70° down
D. 70° right
NOTE: Warm air radiates from the vents at the top of the Touch
Screen possibly causing some surface discoloration over time.
© 2007 Schneider Electric. All Rights Reserved.
11
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Infrared Remote Control
The Color Touch Screen is supplied with a remote control which is
used to select scenes and turn loads on and off or ramp them to a
desired level. The remote control functionality is set up using the
PICED software, and the functions depend upon how the Touch
Screen is programmed. The same remote control can communicate
with multiple Touch Screens installed on the same network. Refer to
the IR Remote Manual for additional information.
Installing the Color Touch Screen with IR Support
HAZARD OF OVERLAPPING RECEPTION ZONES
Install multiple Touch Screens in locations where infrared reception
zones will not overlap when using an infrared remote (IR) control.
Failure to follow this instruction can result in unintended
operation.
Multiple Touch Screens can be installed on any C-Bus™ network.
These units may be programmed to operate dependently or
independently of each other. Be sure to install multiple Touch
Screens in locations where infrared reception zones will not overlap
when using an infrared remote (IR) control.
Figure 2: Infrared Reception Zones
KEY:
1. Room 1
2. Room 2
A. Infrared reception
zone
B. Touch Screen
C. Infrared remote
control
12
INCORRECT
CORRECT
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
SAFETY PRECAUTIONS
This section contains important safety precautions that must be
followed before attempting to install or maintain electrical
equipment. Carefully read and follow the safety precautions below.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
x
This equipment must be installed and serviced by qualified
electrical personnel.
x
Apply appropriate personal protective equipment (PPE) and
follow safe electrical work practices. See NFPA 70E.
x
Turn off all electrical power supplying this equipment before
working on or inside the equipment.
x
Always use a properly rated voltage sensing device to confirm
that power is off.
x
Replace all devices, doors, and covers before turning on power
to this equipment.
Failure to follow these instructions will result in death or
serious injury.
© 2007 Schneider Electric. All Rights Reserved.
13
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
INSTALLATION
Options for Mounting the Color Touch Screen
The Color Touch Screen can be mounted in the Wall Box
(SLC5000CTCWB), Nail Bracket (SLC5000CTCNA), or
Plasterboard Bracket (SLC5000CTCRM) depending on the
installation conditions.
Use a Wall Box under the following conditions:
x
Walls are solid, such as brick or stone.
x
A high level of RF shielding is desired.
x
Wall construction is unfinished framed stud (wood or metal).
Use a Nail Bracket under the following conditions:
x
There is existing finished wall construction.
x
Stud walls such as wood frame internal walls exist.
x
It is possible to nail or screw into a wall frame.
Use a Plasterboard Bracket under the following conditions:
x
The Touch Screen is being mounted into a plasterboard wall.
x
There is sufficient clearance inside the wall's cavity to rotate the
bracket during installation.
Refer to the "Wall Box", "Nail Bracket", or "Plasterboard Bracket"
instruction bulletin for specific mounting instructions.
14
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Mounting the Power Supply
The Square D® Clipsal® Color Touch Screen Power Supply
(SLC5000CTCPS) must be used with the Color Touch Screen.
Installing the power supply above the Touch Screen is
recommended. Consider the following factors when installing:
x
The use of conduit is recommended. Feed the DC output cable
to the Touch Screen through the conduit.
x
Confirm the power receptacle used to provide power is limited to
the range specified. Refer to the "Specifications" section of this
manual for the specific supply voltage.
NOTE: Although the Power Supply uses transient protection
circuitry, it is recommended that external power surge protection
devices be used to enhance system immunity to power surges.
Refer to the "Color Touch Screen Power Supply" installation
instructions for instructions and additional information.
© 2007 Schneider Electric. All Rights Reserved.
15
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Mounting the Color Touch Screen
The Touch Screen is mounted in a Wall Box, Nail Bracket, or
Plasterboard Bracket. Refer to the "Options for Mounting the Color
Touch Screen" section for information on the three mounting
options. Follow the general steps below to mount the Touch Screen
and refer to each bracket's respective manual for any specific
mounting details.
1. Confirm all cables are fed through the selected mounting unit
(the wallbox, plasterboard bracket, or nail bracket).
2. Confirm all cables are fed through conduit, or through conduit
knockouts using another approved method to secure the
conductors.
3. Hold the Touch Screen up to the mounting unit and plug in the
cables. Refer to the "Connections to the Color Touch Screen"
section of this manual for connection information.
4. Insert the Touch Screen into the mounting unit.
5. Align the four mounting holes on the Touch Screen with the
mounting holes on the mounting unit.
NOTE: Confirm all cables are clear of the mounting screws
before securing the Touch Screen to the mounting unit.
6. Screw the Touch Screen to the mounting unit with the four
mounting screws provided. Do not over tighten.
16
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Attaching and Removing the Touch Screen Cover Plate
It is recommended to attach the cover plate after the connections
and software project transfer are complete.
Follow the steps below to attach the cover plate.
1. Position the cover plate over the Touch Screen with the infrared
and indicator windows on the right side.
2. Line the clips on the left underside of the cover plate just left of
the matching clips on the Touch Screen.
3. Firmly push the left side of the cover plate onto the Touch
Screen and then push right. Confirm the left clips aligned in step
2 snap together.
4. Push the right side of the cover plate right, and onto the Touch
Screen until the clip on the right underside of the cover plate
snaps into place. Refer to the "Attaching the Cover Plate" figure.
Figure 3: Attaching the Cover Plate
KEY:
1. Position the cover
plate
A. Clips
2. Press cover onto
Touch Screen and
push right
3. Apply forward, right
pressure to the cover's
right side.
© 2007 Schneider Electric. All Rights Reserved.
17
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
The Touch Screen's cover plate may need to be removed for tasks
such as resetting the software. Follow the steps below to remove
the cover plate.
1. Firmly push the release lock (located on the right side), in toward
the touch screen.
2. While holding the release lock in, lift the right side of the cover
plate up and right to disengage the clip. Refer to the "Removing
the Cover Plate" figure.
3. Push the cover plate left to disengage the left locks and remove.
Figure 4: Removing the Cover Plate
KEY:
A. Push the release
lock
B. Lift off and to the
right to disengage the
clip, then swing to the
left
18
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
CONNECTIONS TO THE COLOR TOUCH SCREEN
Connections are determined by the Touch Screen's specific install
scenario. Some, or all of the connections described in this section
may be used. Refer to the "Connection Types for the Color Touch
Screen" table for a list of all ports, and their intended uses. For
additional connection information, refer to the connector's specific
section in this manual.
Table 3: Connection Types for the Color Touch Screen
Connection
Intended Use
Compact flash card
Factory fitted and easily removable for software upgrades.
C-Bus
Connects the Touch Screen to the C-Bus network.
RS-232
Connects external devices such as security equipment.
IR Input
Enables the infrared remote.
Audio Line In/Out
Provides audio to and from the Touch Screen.
USB
Provided for future capabilities.
Video Out
Allows the transfer of video from the Touch Screen to an
external monitor or television.
PS/2
Temporarily connects devices such as a mouse or keyboard
to assist in Touch Screen configuration.
DC Power Input port
Connects the Color Touch Screen Power Supply
(SLC5000CTCPS).
Ethernet
Permanently connects to a LAN for Touch Screen
configuration.
RJ-45
Temporarily connects to a PC for Touch Screen configuration.
NOTE: Cables for all connections are provided by the user except
the red crossover network cable for a RJ45 connection.
NOTE: Some connector ports on the Touch Screen look similar
such as the Ethernet and RJ45 connectors. Refer to the specific
connection information in each section to confirm cables are
connected to the Touch Screen using the proper ports.
© 2007 Schneider Electric. All Rights Reserved.
19
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Figure 5: Color Touch Screen Back Side Connectors
KEY:
A. Ethernet
B. Compact flash card
(factory fitted)
C. C-Bus
D. RS-232
E. IR input
F. Audio line in
G. Audio line out
H. USB
I. Video out
J. PS/2
K. DC power
Figure 6: Color Touch Screen Front Side Connector
KEY:
A. RJ45 input
20
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Connecting the Color Touch Screen to the C-Bus Network
The C-Bus network is connected to the Color Touch Screen through
the polarity sensitive RJ45 inputs located on the top back side of the
Touch Screen. Connect the devices with Category 5 unsheilded
twisted pair C-Bus network cable, and a wired RJ45 plug. Refer to
the "Wiring Connections Key Diagram" figure, and the "RJ45 Pin
Connections" table for wiring and pin connection information.
NOTE: The Category 5 unsheilded twisted pair C-Bus network cable
and the wired RJ45 plug are provided by the installer.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Do not connect line voltage to wired Touch Screens.
Failure to follow this instruction can result in personal injury or
equipment or property damage.
© 2007 Schneider Electric. All Rights Reserved.
21
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Figure 7: Wiring Connections Key Diagram
KEY:
A. C-Bus positive (+): blue +
orange
B. C-Bus negative (-):
blue/white + orange/white
C. Remote OFF: brown +
brown/white
D. Remote ON: green +
green/white
Table 4: RJ45 Pin Connections
22
RJ Pin
C-Bus Connection
Color
1
Remote ON
Green/White
2
Remote ON
Green
3
C-Bus Neg (-)
Orange/White
4
C-Bus Pos (+)
Blue
5
C-Bus Neg (-)
Blue/White
6
C-Bus Pos (+)
Orange
7
Remote OFF
Brown/White
8
Remote OFF
Brown
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Connecting Serial Communications to the Touch Screen
External devices such as security and control equipment are
connected to the Color Touch Screen through the RS-232 port. The
"RS-232 Connection" table describes the standard EIA 574 pinouts
used for the RS-232 connection.
NOTE: Use a shielded data cable to connect any external device.
Limit cable length to 49 feet (15 meters) for communication up to
19,200 bps, or 25 feet (7.5 meters) for communication up to
38,400 bps.
Table 5: RS-232 Connection
Pin No. Name
Description
1
DCD
Data Carrier Detect
2
RD
Receive Data
3
TD
Transmit Data
4
DTR
Data Terminal Ready
5
GND
Ground
6
DSR
Data Set Ready
7
RTS
Request to Send
8
CTS
Clear to Send
9
RI
Ring Indicator
HAZARD OF UNSTABLE OPERATION OR EQUIPMENT
DAMAGE
x
Do not connect C-Bus network to a PC communications port.
x Do not Megger® test C-Bus or RS232 data cabling or terminals.
Failure to follow this instruction can cause instability or
damage to the C-Bus network or other equipment connected to
the network.
© 2007 Schneider Electric. All Rights Reserved.
23
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Connecting through the Ethernet or RJ45
The Touch Screen is configured using PICED configuration software
installed on a personal computer (PC). The PICED software is used
to create a unique software project that is transferred to the Touch
Screen through the Color Transfer Utility software. Refer to the
"About the Color Touch Screen Software Project" section of this
manual for instructions on the software transfer.
There are two connection methods to complete the software project
transfer:
x
through an ethernet connection on the back of the Touch
Screen,
x
or through an RJ45 Connection on the front of the Touch Screen
under the cover plate.
Connecting through the ethernet port is recommended in the
following conditions:
x
More than one Touch Screen is being configured.
x
The Touch Screens are connected through a LAN.
x
Connection from the Touch Screen is permanent.
The ethernet port is located on the top right back corner of the
Touch Screen. When connecting the PC through a LAN, use a
standard ethernet cable.
NOTE: The ethernet cable is provided by the user.
The RJ45 connection is recommended in the following conditions:
x
A PC is connected directly to the Color Touch Screen.
x
Touch Screens are configured one at a time by directly
connecting each Touch Screen to the PC.
x
Connection to the Touch Screen is temporary.
The RJ45 port is located on the front, right side of the Touch Screen
under the cover plate. Use the Category 5 crossover ethernet patch
cable provided when connecting the PC through the RJ45 port.
Refer to the "Category 5 Crossover Ethernet Patch Cable Wiring
Assignments" table for wiring information.
24
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Table 6: Category 5 Crossover Ethernet Patch Cable Wiring
Assignments
Connection Connection Color
A
B
1
3
Green/White
2
6
Green
3
1
Orange/White
4
4
Blue
5
5
Blue/White
6
2
Orange
7
7
Brown/White
8
8
Brown
Connecting Devices through the PS/2 Connection
A keyboard or mouse is temporarily connected through the PS/2
port to assist in Touch Screen configuration and support
applications. Prior to attaching a mouse, connect a "Y" adapter to
the PS/2 port. A keyboard can be attached directly to the PS/2 port,
or through a "Y" adapter.
NOTE: It is recommended that devices connected through the PS/2
port are used to assist during installation only, and are not
permanently connected to the Touch Screen.
Caring for the Color Touch Screen
Remove the clear protective film from the Color Touch Screen only
after wall construction, finishing activities (such as plastering,
sanding, and painting), and installation are complete.
Use the soft, lint-free, LCD cleaning cloth provided to clean the
Color Touch Screen. If needed, spray the cloth with a mild cleaning
solution such as window cleaner and wipe the screen, then
surrounding areas. Do not spray cleaners directly on the Touch
Screen. When complete, wipe the Touch Screen dry. Do not use
abrasive cleansers, clothes, or scouring pads.
© 2007 Schneider Electric. All Rights Reserved.
25
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Connecting the Audio and Infrared
Infrared, audio line in, and audio line out connections are color
coded as red, blue, and green ports respectively on the back side of
the Color Touch Screen. Connections are compatible with a 0.14 in.
(3.5 mm) mono socket for the infrared input, and 0.14 in. (3.5 mm)
stereo sockets for the audio lines.
Loop the audio and infrared cables through the large ferrite filter
provided before connecting to the Touch Screen to provide
additional filtering and compliance with electromagnetic compatibility
(EMC) regulations.
Connecting the Video
An RCA video line out connection is color coded as a yellow port,
and located on the bottom right side (when viewed from the front) of
the Color Touch Screen. Connection to the video line enables the
Touch Screen's display to be viewed on a TV or monitor with
composite video input.
Fit the small ferrite filter provided over the video cable before
connecting to the Touch Screen to provide additional filtering and
compliance with electromagnetic compatibility (EMC) regulations.
26
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
PROGRAMMING THE COLOR TOUCH SCREEN
A software project is a unique program created to allow the installer
and user to configure and customize the Touch Screen. The
software project is created, and then exported to an archive folder
where it can be transferred to the Touch Screen. Refer to a Square
D® Lighting Control representative or the installer for information on
creating and archiving a software project.
The customized software project is ready to transfer to the Touch
Screen after the project is complete and archived using Clipsal
C-Bus Toolkit software.
To transfer a software project, a PC connection, and installation of
Clipsal's C-Bus Toolkit software and Piced software is required. All
software is available from the Clipsal Integrated Systems (CIS)
website at (http://www.clipsal.com/cis).
After the software is installed, connect the Touch Screen to the
C-Bus Network. Refer to the "Connecting the Color Touch Screen to
the C-Bus Network" section for connection and wiring information.
Refer to the "C-Bus Toolkit Help" in the Toolkit software for
additional connection and startup information.
Transferring the Customized Software Project to the Color Touch Screen
The PICED software includes a Touch Screen transfer utility that is
used to upload a software project from the project archive to the
Touch Screen. After the software project is installed, configuration
functions, such as setting the time on the Touch Screen, can be
completed.
The transfer instructions provided are about how to install a project
from a PC using a direct Ethernet connection.
NOTE: It is also possible to install software projects to multiple
Touch Screens through a common DHCP network, or a network
where each Touch Screen has been configured with an appropriate
static IP Address. When connecting through a DHCP network, wait
approximately 3 minutes for the network connection to be enabled.
© 2007 Schneider Electric. All Rights Reserved.
27
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Before You Begin and Starting the PICED Software
Follow the instructions in this section before beginning the software
project transfer.
1. Confirm the following steps are complete before transferring the
software project to the Touch Screen:
28
x
The Touch Screen is plugged into a power receptacle to
automatically power it ON.
x
The PICED software is installed on a PC.
x
The customized software project is complete and added to
®
the project archive. (Refer to the Square D Lighting Control
representative or the installer for information on creating a
software project).
x
The cover plate is removed from the Touch Screen. (Refer to
the "Attaching and Removing the Touch Screen Cover Plate"
section for instructions).
x
The PC is connected to the Touch Screen through the RJ45
connection. (Refer to the "Connecting through Ethernet or
RJ45" section for additional information).
x
The PC is powered ON.
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
2. The following configuration screen is displayed on the Color
Touch Screen when step 1 is complete.
Figure 8: Configuration Startup Screen
3. Double click the PICED icon (shown below) on the PC to open
the PICED software.
Figure 9: Piced Startup Icon
© 2007 Schneider Electric. All Rights Reserved.
29
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Selecting the Project to Transfer
After the PICED software is started, the software project is retrieved
from the archive. The following "Select Project" screen is displayed.
Figure 10: Select Project
KEY:
A. Open an existing
project radio button
B. Open project text
box
C. Next button
1. Select the Open an Existing Project radio button. An Open File
window is displayed.
2. Open a project and click the Next button to continue. The
"Project Type" screen is displayed.
30
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Figure 11: Project Type
KEY:
A. Select the Color CTouch radio button
3. Click the Colour C-Touch radio button under the device type,
and click the Next button. The following "Select a C-Bus Project"
screen is displayed.
Figure 12: Select a C-Bus Project
KEY:
A. Local Machine
radio button
B. Select a C-Bus
project
C. Finish button
© 2007 Schneider Electric. All Rights Reserved.
31
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
4. Click the Local Machine radio button under the C-Gate Server
Location if the Color Touch Screen is connected directly to the
PC through the RJ45 port on the front of the Touch Screen.
NOTE: If the Color Touch Screen is connected through a DHCP
network, click the Remote Machine radio button and assign a
static IP Address.
5. Click the drop down menu under the C-Bus Project and select
the specific project built with the Toolkit software.
NOTE: To enter additional optional information, such as
selecting a default network, adding project details, adding
installer details, and adding project preferences and screen
setups, click the Next button on the "Select a C-Bus Project"
screen. Click Finish at anytime to exit the additional information
screens.
Click the Finish button to continue with the software project transfer.
32
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Saving the Project onto the Touch Screen
After the project is retrieved, it is ready to be transferred to the
Touch Screen. Follow the instructions in this section to start the
color transfer utility and save the project to the Touch Screen.
1. The PICED "Software Revision History" screen is displayed.
Figure 13: Software Revision History
KEY:
A. OK button
2. Review the release notes on the Revision History Screen and
click OK to accept. The software project is displayed in the
PICED software on the PC as shown in the "Start Color Transfer
Software" screen.
© 2007 Schneider Electric. All Rights Reserved.
33
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Figure 14: Start Color Transfer Software
KEY:
A. Software project
screen
B. Color transfer utility
icon
3. Click the PC's Color Transfer Utility icon on PICED toolbar
(labeled on the "Start Color Transfer Software" screen) to start
the software. The "Transfer to Unit" screen is displayed.
NOTE: A message indicating the software project has errors
may be displayed. Often these errors are intentional and
preferred configurations created in the software project. Click the
Yes button on the error message screen to view a project error
report. The report lists all errors found in the project software.
Click OK on the report screen to accept the errors, and click Yes
on the confirmation screen to continue. If the project error is
critical, a critical error message is displayed and the error must
be repaired in the software project before continuing.
34
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Figure 15: Transfer to Unit
KEY:
A. Transfer current
project radio button
B. OK button
4. Click the Transfer current project radio button, then click OK.
The following "Confirm and Save" screen is displayed.
Figure 16: Confirm and Save
KEY:
A. Yes button
5. Click the Yes button to save the software project.
6. The software auto-populates the path to save the software as
shown on the "Save Project File" screen.
© 2007 Schneider Electric. All Rights Reserved.
35
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Figure 17: Save Project File
KEY:
A. Next button
7. Click the Next button (displayed when the project file path is
populated) to accept. The following "Save Font" screen is
displayed.
Figure 18: Save Font
KEY:
A. Review fonts used
to create software
project
B. Next button to
review and save each
font
36
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
8. Click the Next button on the "Save Font" screen to save all
additional fonts used in the software project. The "Save File"
screen is displayed.
Figure 19: Save File
KEY:
A. Archive file name
text box
B. Open folder button
C. Finish button
9.
The archive file name text box is populated with a default
directory to save the project. Click the folder icon to change the
directory, or the Finish button to accept the saves.
NOTE: It may take several seconds to complete the software
project save.
© 2007 Schneider Electric. All Rights Reserved.
37
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Selecting a Network and an IP Address
If there are multiple network adaptors enabled on the PC, the
following "Select Network Card" screen is displayed after the project
is saved to the Touch Screen.
NOTE: If only one network is enabled, the user is NOT instructed to
select a network. Instead, the software searches for the Touch
Screens on the one network, and the "Unit Selection" screen is
displayed. Refer to the “Selecting a Touch Screen and Uploading
the Project” section.
Figure 20: Select Network Card
KEY:
A. Select a network
adaptor
B. Next button
1. Check the box beside the name of the network adaptor
connected to the Touch Screen. Click the Next button.
NOTE: The software searches for the Touch Screen on the
selected network. Touch Screens recently installed and using a
static IP address may not be found by the software and a Select
Touch Screen Network screen is displayed. If the Touch Screen
is recognized and the "Unit Selection" screen is displayed,
proceed to the “Selecting a Touch Screen and Uploading the
Project” section of these instructions.
38
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
If the software did not recognize the Touch Screen, the "Select
Touch Screen Network" screen is displayed.
Figure 21: Select Touch Screen Network
KEY:
A. Standalone radio
button
B. Next button
2. Select the Standalone radio button on the "Select Touch Screen
Network" screen and click Next. An IP address compatible with
the PC is automatically selected by the software as displayed on
the "Suggested IP Address" screen.
Figure 22: Suggested IP Address
KEY:
A. Next button
© 2007 Schneider Electric. All Rights Reserved.
39
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
3. Click the Next button to accept and send the suggested IP
address to the Touch Screen. The "Confirming the New Direct IP
Address" screen is displayed on the Touch Screen's monitor.
Figure 23: Confirming the New Direct IP Address
4. Confirm the IP address displayed on the Touch Screen matches
the suggested IP Address on the PC and press the Touch
Screen's Yes button.
NOTE: To assign a specific IP Address on the Color Touch
Screen rather than using the suggested IP address, touch the
No button on the "Confirming the New Direct IP Address" screen
and type the new IP address.
The Touch Screen displays an information message to confirm the
IP Address is set.
Figure 24: IP Address Information
Touch the OK button to confirm the IP Address on the "IP Address
Information" screen.
40
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Selecting a Touch Screen and Uploading the Project
This section provides instructions on selecting the Touch Screen to
transfer the project to, and transferring the project.
The PC displays the "Unit Selection" screen after an IP address is
assigned.
Figure 25: Unit Selection
KEY:
A. Select the Touch
Screen (Unit)
B. Click the Next
button to add optional
information
C. Finish button
1. Click to highlight the name of the Touch Screen displayed in the
"Unit Selection" screen. Click the Finish button to complete.
NOTE: If the Touch Screen to select is not displayed on the
"Unit Selection" screen, click the Next button to return to the
"Select Touch Screen Network" screen. Follow the instructions
in the “Selecting a Network and an IP Address” section to select
a new IP address.
The "Transfer Utility Information" screen is displayed on the PC. The
screen has three tabs: Information, Control, and Transfer. The tabs
provide software project transfer information, file location settings,
and project settings.
© 2007 Schneider Electric. All Rights Reserved.
41
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Figure 26: Transfer Utility Information
KEY:
A. Information tab
B. Control tab
C. Transfer tab
2. Click the Transfer tab at the top of the "Transfer Utility
Information" screen. The "Transfer Page" screen is displayed.
Figure 27: Transfer Page
KEY:
A. Select project
location button
B. Project file location
field
C. Transfer project to
Touch Screen button
42
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
3. Paths from a project location to a PC or a Touch Screen are
mapped on the "Transfer Page" screen. Confirm the Project File
Location field is auto-populated.
NOTE: Click the Select Project Location '...' button beside the
Project File Location field if the Project File is not autopopulated. Select the project archive to transfer and click OK to
populate the Project File Location field.
4. The Transfer Project to C-Touch Colour button is enabled when
the "Project File Location" field is populated. Click the Transfer
Project to C-Touch Colour button to add the software to the
Touch Screen. The project may take several seconds to transfer
depending on the size.
The following "Upload Information" screen is displayed when the
software transfer is complete.
Figure 28: Upload Information
5. Click the OK button to confirm the project successfully
transferred.
© 2007 Schneider Electric. All Rights Reserved.
43
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Project Settings and Preferences
Common project settings and preferences for the Touch Screen are
located under the control tab on the PC's "Transfer Utility
Information" screen. To modify project settings follow the
instructions below:
1. Click the Control tab on the PC's "Transfer Utility Information"
screen to change project settings. The following "Control Page"
screen is displayed.
Figure 29: Control Page
KEY:
A. Stop HomeGate
button
B. Enable logging
button
C. Set time button
D. Rename Touch
Screen button
2. If needed, click the Stop HomeGate button to toggle between
starting and stopping the HomeGate to reset the PC to Color
Touch Screen connection.
3. If troubleshooting is required, click the Enable Logging button to
track and log events on the Color Touch Screen.
4. Click the Set Time button to link the time on the Touch Screen
with the time displayed in the lower right corner of the PC.
NOTE: Confirm the time on the PC is correct. Double click the
time displayed in the bottom right corner of the PC to adjust the
PC's time. There is no confirmation or user action required to
confirm the time on the Touch Screen is linked with the time on
the PC.
44
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
5. Type a name in the field beside the Rename C-Touch Colour
button then click the Rename C-touch Colour button. The
following "Rename Confirmation" screen is displayed.
NOTE: Renaming a Touch Screen is useful when multiple Touch
Screens are connected to a LAN, and when the Touch Screen is
controlled by an external device.
Figure 30: Rename Confirmation
6. Click the Yes button to confirm the Touch Screen name change.
After the software project transfer is complete, and project settings
and preferences are selected, click the File button on the c-touch
colour transfer utility toolbar, and select Exit to close the PICED
software. Disconnect the PC. Refer to the Color Touch Screen
User's Guide for information on care and use of the Color Touch
Screen.
Figure 31: Closing the C-Touch Colour Transfer Utility
KEY:
A. File button on the
Colour Transfer Utility
Screen
© 2007 Schneider Electric. All Rights Reserved.
45
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Resetting the Color Touch Screen's Software
The Touch Screen's software is restarted by pressing the reset
button located in the bottom right front corner of the Touch Screen
under the cover plate. Refer to the "Attaching and Removing the
Touch Screen Cover Plate" section for instructions on removing the
cover plate.
Refer to the "Touch Screen Reset Button" figure below.
Figure 32: Touch Screen Reset Button
KEY:
A. Cover plate release
latch
B. Reset button
C. IR sensor
D. Light sensor
46
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
SPECIFICATIONS
The following tables provide specifications for the Color Touch
Screen (SLC50X0CTC).
Table 7: Display/Viewing Area Specifications
Display Type
6.4 in. (16.3 cm) TFT Color Active Matrix LCD
Display Resolution
640 x 480 pixels
Display Luminance
300 cd/m
Display Contrast Ratio
better than 100:1
Viewing Angle
left, right, down: 70º; up: 40º
Viewing Area (HxV)
5.5 x 3.8 in. (130.6 x 97.0 mm)
Backlight Lifetime
(Typical)
50,000 hours, factory exchangeable
Touch Surface Durability 35 million touches in any one location, 1 million touch slides
Touch Overlay Type
Resistive
Status Indicators
User configurable
Table 8: Color Touch Screen Voltage, Processor, Capacity and
Memory Specifications
Supply Voltage*
5.6 V DC, 30W maximum via power pack
Processor
VIA Eden Chipset, 300 MHz
Capacity
Use the C-Bus Calculator to evaluate the total network
current load
Warm-up Time
2 minutes
Memory
256 MB compact flash memory, pre-programmed with panel
firmware
Backup Memory
Lithium battery retains current date and time for 5 years
*The Color Touch Screen Power Supply (SLC5000CTCPS) must be
used to exercise the warranty. Refer to the "Color Touch Screen
Power Supply" installation instructions for Power Supply information.
© 2007 Schneider Electric. All Rights Reserved.
47
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Table 9: C-Bus Specifications
C-Bus Supply Voltage
15 to 36 V DC @ 20 mA required for normal operation. Does
not provide current to the C-Bus network
C-Bus Control Functions
Load switching and dimming, scene control, scheduling
C-Bus Connection
2 x C-Bus RJ45 (parallel)
C-Bus System Clock
Software selectable
Table 10: Components and Connectors Specifications
Front
- Ethernet 10/100/RJ45 terminal (under cover plate)
- Speaker (under cover plate)
- Infrared receiver
- RS-232 via DB 9 terminal
Back
- 2 x C-Bus RJ45 (parallel)
- Ethernet 10/100/RJ45 terminal
- Composite Video Out (75 : RCA) PAL or NTSC selectable
- RS-232 via DB 9 terminal
- USB type A
- Audio line in (0.14 in. (3.5 mm) stereo)
- Audio line out (0.14 in. (3.5 mm) stereo)
- Infrared In (0.14 in. (3.5 mm) mono)
- PS2 keyboard
- 7 pin power
Table 11: Operating Ranges
Operating Temperature
Range
50 to 86°F (10 to 30°C)
Operating Humidity
Range
10 to 90% RH (non-condensing)
Table 12: Color Touch Screen Physical Characteristics
48
External Dimensions
(WxHxD)
9.8 x 6.9 x 2.9 in. (246 x 173 x 72.5 mm) excluding the cover
plate
Protrusion from Wall
0.9 in. (23.5 mm) including the glass cover plate
Mounting Depth (into
wall)
2.2 in. (54 mm)
Mounting Centers
(HxV)
8.5 x 4.5 in. (212.5 x 112 mm)
Weight
3 lbs (1375 g) excluding the cover plate
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
Figure 33: Color Touch Screen Physical Dimensions Front View
Figure 34: Color Touch Screen Physical Dimensions Side View
KEY:
A. Protrusion from the
wall: 0.9 in. (23.5 mm)
B. Mounting depth into
wall: 2.2 in. (54 mm)
C. Total depth
(excluding cover
plate): 2.9 in. (72.5
mm)
D. Cover plate
© 2007 Schneider Electric. All Rights Reserved.
49
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
63249-420-209A1
04/2007
Table 13: Specifications - Infrared Remote Control
Supply Voltage*
3 V DC required for normal operation. Transmission range
reduces with decreasing battery voltage
Battery
Lithium "coin" battery CR2025 (or equivalent)
Battery Shelf Life
Approximately ten years
Infrared Transmission Approximately 26.3 ft (8 m) at 90° or 13.1 ft (4 m) at 60° to the
Range
Color Touch Screen
Control Functions
8 membrane buttons comprising 5 general purpose buttons, 1
master off button, up/down buttons
Dimensions (WxHxD)
3.4 x 2.2 x 0.3 in. (86 x 54 x 8 mm)
Weight
0.06 lbs (28 g)
Color
black
Refer to the Infrared Remote Control User's Guide for additional
information.
50
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
STANDARDS
Table 14: U.S. and Canadian Product Safety Standards and U.S.
FCC Regulations
Standards/Regulations
Title
CSA C22.2 No. 205
Signal Equipment
UL916
Energy Management Equipment
FCC Part 15
Part 15, Class B Digital Device for Home or Office Use
© 2007 Schneider Electric. All Rights Reserved.
51
Square D® Clipsal® Color Touch Screen
Instruction Bulletin
SUPPORT AND SERVICE
Contact the Square D Customer Information Center for technical
support by phone at 1-888-Square D (1-888-778-2733) or e-mail at
[email protected].
Contact your local Square D service representative or Square D®
Clipsal® certified installer for repairs or service to your network.
You may also find helpful information on our web site at
www.squaredlightingcontrol.com.
Schneider Electric, USA
295 Tech Park Drive
La Vergne, TN, 37086
1-888-SquareD (1-888-778-2733)
www.squaredlightingcontrol.com
Electrical equipment should be installed, operated, serviced, and
maintained only by qualified personnel. No responsibility is assumed by
Schneider Electric for any consequences arising out of the use of this
material.
, Clipsal, and C-Bus, are trademarks or registered
Square D,
trademarks of Schneider Electric and/or its affiliates in the United States
and/or other countries.
© 2007 Schneider Electric. All Rights Reserved.
63249-420-209A1
04/2007