SPECIFICATIONS FOR
30 YARD OPEN TOP ROLL-OFF CONTAINER
4 YARD CAPACITY WASTE COMPACTION UNIT
40 YARD WASTE CONTAINER FOR COMPACTION UNIT
Listed below are the specifications for purchase of the following waste hauling
equipment: Thirty (30) yard capacity open top cable hoist type rolloff containers.
The bath tub style containers will not be accepted; Standard square bottom design
only. Amount-17
Four yard capacity compaction units with fabricated hopper. Amount-4 units
Forty (40) yard capacity compactor compatible breakaway cable hoist waste
containers. Amount-5.
The contractor will be responsible for delivery to and installation of two
compaction units with containers to the Crisfield Transfer Station and two
complete units to the Mt. Vernon Transfer Station. All labor, supplies, and
equipment necessary to complete the installation of the compaction units will be
the responsibility of the contractor. All open containers will be delivered to either
to the Somerset County Landfill or the Somerset County Roads Department.
Service for the compaction units must be available within a 100 mile radius of the
Crisfield Transfer Station.
30 Yard Open Top Cable Hoist Waste Container Specifications
1. Length of container
2. Width
3. Inside height
4. Floor5. Understructure
6. Long rails
7. Bullnose
8. Hook plate
9. Push plate
10. Cable hookup
11. Hook
.
12 Nose roller
13. Wheel axle
14. Wheels
15. Side walls
16. Door
22 feet 8 inches
8 feet
Floor to top rail-62 inches
2 pieces ¼” sheet steel butt welded
3” channel 4.l/ lbs/ft on 16” apart
2” x 6” x ¼” tubing
Solid 1 ¼” plate burnout
23” x 15” x 3/4”
26” x 16” x 3/16”
1 ¼” flame cut steel inserted through hook
plate, weld both sides
4” diameter x 6” long solid tubing with
grease fittings
1 ½” solid round bar
Steel 8” x 10” long rear, 8” x 6” long front
12 gauge steel No bent top rails
10 gauge steel – 3” x 4” x 11 gauge
structural tubing with 2- 3” x 4” x 11 gauge
tube cross members, 3 heavy duty hinges
17. Bulk head
18. Top Rail
19. Side Post
20. Rear Corner Post
21. Tailgate sheet
22. Tailgate latch
23. Tailgate Frame
24. Hinges:
25. Paint
26. Ladder
27. Container Front
28. Container Style-Cable Hook
with grease fittings, 30” handle, 2 latches,
1 door fork, and ¼” chain lock. Latch
system- uplift
10 gauge steel
3” x 4” x 7” gauge tubing
3” x 5” x 11” gauge formed on 24”
centers with 1” drain port/weep hole
3 ½” x 7” x 3/16” formed
10 gauge
Vertical lift handle
Vertical 3” x 4” x 7 gauge tubing,
horizontal 3” x 5” x 10 gauge formed tube
with dirt shedder top.
Heavy duty machine type, three on 62” and
higher
Chemically degreased, welds ground
smooth and sand blasted. Prime and paint
one color with an exterior latex
paint. Color-Blue- Shade to be decided by
the County after award of contract.
Ladder and tarp rails on each side made
with 5/8” hot rolled rounds
Container front- 11 gauge steel with a 3” x
4” x 11 gauge top cap and 11 gauge dog
box which houses the hook station. Dog
box should be supported by 2” X 6” X 11
gauge structural tubing running from top
to bottom of front and supported by 2” x
6” x 11 gauge cross members. Corners are
to be covered with 4” x 8: x 11 gauge
corner angles.
Containers shall be cable/hook and rails
compatible with existing County owned
recycling containers.
Delivery Date- July 1, 2014
Delivery location-Somerset County Landfill or Somerset County Roads
Department Westover, Md.
Number of open top 30 yard containers- 17
40 Yard Cable Hoist Octagonal Packer Receiver Waste Container
for Compaction Unit
1. Length2. Width
3. Understructure
4. Long rails
5. Bullnose
6. Floor
7. Push plate
8. Hook plate
9. Wheels
10. Wheel axles
11. Nose roller
12. Side wall and roof
13. Bulkhead
14. Front Post
15. Tailgate sheet
16. Tailgate frame
17. Rear Corner Post
18. Tailgate latch
19. Hinges
20. Paint
21. Fire Port
22. Ratchet Cam Latch
23. Container front
24. Ratchet Cam Latch Hole
22 feet 8 inches
3” channel 4.1 lbs/ft at 16” apart
2” x 6” x 1.4” tubing
Solid 1 ¼” plate burnout
3/16” 2 pieces butt welded
26” x 16” x 3/16”
23” x 15” x ¾”
8” x 10” long rear only
1 ½” solid round bar
4” diameter x 6” long
7 gauge with 5” taper per side from rear to
front
7 gauge
3” x 5” formed on 24” centers
7 gauge
Vertical and horizontal 3” x 4” x 7 gauge
Tubing
2” x 6”x ¼” tubing
Vertical lift handle
Heavy duty machine type, three on 62” and
Higher
Chemically degreased. All welds ground
smooth and sand blasted. Prime and paint
one color with an exterior latex paint. Color
blue-Shade to be determined at the time of
the contract.
Minimum 2 “ fire port with screw cap at the
midway point on both sides of the box
One each side to ratchet the waste receiver
container to the compaction unit.
11 gauge steel dog box which houses the
Hook station. Dog box should be supported
by 2” x 6” x 11 gauge structural tubing
running from top to bottom of the front
and supported by 2” x 6” x 11 gauge cross
members. Corners are to be covered with
4” x 8” x 11 gauge corner angles.
The box corner post will be reinforced with
an 8”x 8” ¾” thick steel plate with a 4”x4”
cutout hole for the ratchet latch. 2 – 16 inch
long by ½” thick gussets will be installed on
each corner for additional strength.
25. MAWS 15’ guide tracks with stops for each unit. Total of 4 units
26. Number of containers-5
27. Number of cloth cover/diapers for the open end. (6)
The waste containers shall be compatible with the compactor units supplied. The
boxes will be designed to break away from the stationary compaction unit.
The container will be supplied with rubber gasket material to prevent leakage
between the compactor and the waste container box opening.
The container will be constructed for a cable hoist roll-off system compatible with
the recycling containers currently owned by the County.
Number of containers- 5
Number of cloth opening covers- 6
Delivery Date- July 1, 2014
Delivery location- Somerset County Landfill or Somerset County Roads
Department-
Stationary 4 Yard Compactor Unit
The following are the specifications for 4 four cubic yard compaction units to be
delivered to and installed at the following locations: Crisfield Transfer Station-Rt.
413, Crisfield, Md., Mt. Vernon Transfer Station, Mt. Vernon Road, Princess
Anne, Md. Each transfer station will receive 2 units. The units will be stationary
and only the 40 yard container will be removed for disposal of the waste.
The bid will include installation of the compactors, electrical supplies, labor, and
all other parts necessary to complete the project. The equipment supplier will
provide 8 hours of Operation and Maintenance Training for Solid Waste and
Maintenance personnel.
1. Charge Box
2. Clear top opening
3. Overall dimension length
4. Weight with power unit
5. Cycle time
6. Ram Force
7. Ram penetration
4.0 cubic yards
65” length x 60” width
180” x 72.5” Height 62”
6,600 to 6,700 lbs.
50-55 second cycle –
Multicycle-Three
passes
48,000 lbs.
14”
30.50”
½” steel with ¾” stiffener
plates
c. Ram base plate
3/8” steel with 10 gauge
formed stiffeners
d. Ram top plate
¼” steel with 10 gauge
formed stiffeners
e. Ram side plates
¼” formed plate
8. Electric
208/230/460, 3 phase 60Hz
9. Motor
15 HP with 3 Phase motor
starter & heaters
10. Power box
UL rated, TEFC housingMust meet ANSI
Z 245.2 Safety Standards
11. Electrical Panel
NEMA 4 Weather Proof
Gasketed Panel
12. Automatic Cycle Operation
Turn key, push button start
for three
Cycles with manual cutoff
button
13. Low Temperature Oil:
0 Degree Fahrenheit
Operation
14. Heavy Duty 1 3/8” ratchet binders with 1” thick hooks rated at 70,000 lbs.
15. Override-Packet-Pressure-Boost
16. Automatic Maintenance Scheduler
17. Container full light and auto shutdown18. Oil filled pressure gauge on 15” hose
1 gauge per unit- 0 to 3,000
psi.
19. Key start-auto
20. Push button start for three cycles
21. Three sided hopper built on site
Side feed-walk-up
Application primed and
painted to match the
container color. (Blue)
22. Hydraulic oil tank heater for each unit-Total 4
23. ½” thick ram floor
24. Heavy duty breaker bar
8” x 8” x 1” angled steel
25. Compactor head floor
½” steel with 10 gauge
channels at 12” spacing
26. Compactor head sides
¼” steel formed vertical and
formed horizontal stiffeners
27. Compactor head top deck
12 gauge steel
a. Ram height
b. Ram face plate
28. 24 Volt operator controls
All equipment must be available for installation by July 1, 2014. Payment for
equipment will be made on or after July 1, 2014.
The County is currently contracting for waste hauling services. Each of the two
transfer stations has two compaction units in place. The County will request that
the current contractor remove one compaction unit at a time. Installation of each
new compactor with container must occur within one (1) week after notification
by the County to proceed.
The contractor must be able to provide technical or mechanical onsite service to
each of the two transfer station sites from within a 100 mile radius.