Stanza™
Standalone and Integrated System
System Specification
086-128 1 07.15.09
Stanza™ | Shading System
The Stanza Shading System utilizes
ultra-quiet precision controlled contact
closure electronic drive units. Stanza drive
units are available for roller shades and
drapery tracks. The Standalone System
operates independent of Stanza guest room
light controls. The Integrated System offers a
complete lighting control solution.
Features
• Operates directly via contact closure
• Integrates with Lutron® Stanza lighting control
systems (SZ-IO required)
• Ultra-quiet operation: will not exceed 44 dBA
measured 1 m (3 ft) from the Drive
• Offers one favorite preset with optional
infrared remote control
• Drives can be stopped while moving with
the touch of any button of any keypad or IR
Remote
• Stanza drives are available for Roller 100
shade and D70 and D105 drapery systems
• All drives start, move and stop with precision
• Can be installed in new construction or
retrofit application
• Power failure memory for the lifetime of
the product
• IR remotes offers programmable stop
points. The Drive tracks the position of the
shade or drape and is able to adjust it to
preset locations at the touch of a button
• Easy-to-read and easy-to-use controls are
immediately understood
• Offers two programmable groups with IR
remote
• 24 V
low-voltage power
• 8 year limited warranty
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Stanza Shade
Stanza Drape
Page 1
Stanza™
Standalone and Integrated System
System Specification
086-128 2 07.15.09
Specifications
Power
Grouping
Operating voltage: Low-voltage 24 V--- power
supply required
• Control system power supply offers (spike and
brownout) over voltage protection (+/- 10% of line
voltage) for all devices in the system.
• Power supply provides appropriate Electro Static
Discharge (ESD) protection for all devices in the
system
• Power must be derived from a Lutron® approved
power source
•
System Capacity
Maximum of 4 drives per contact closure output
•
Performance
Each Drive stores presets positioned at any stop point
along the shade’s travel, as well as full open and full
close shade limits using an IR remote
• Preset points can be located at any point between
the open/close limits and are adjustable with a 5
second button push and hold from the optional
IR Remote.
• Each Drive is capable of stopping with the accuracy
of 0.125 in (3 mm) steps for the entire travel of
the shade or drape
• Favorite preset can be recalled from IR transmitter
• Open and close limits are programmable from the
Drive or the optional IR Remote
• All system components are Electro Static
Discharge (ESD) protected
• For systems with multiple Drives, shades smoothly
move in unison and precise alignment within 0.125 in
(3 mm) accuracy at all times
•
Job Name:
Job Number:
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Up to 2 groups of Stanza Drives can be controlled
with a Two Group Standalone Keypad
• Up to 2 groups of Stanza Drives can be controlled
with a SZ-IO Contact Closure Interface
• Up to 4 EDU’s can be wired to a Stanza Standalone
shade keypad contact closure output
• The Stanza EDU accepts class 2, dry contact
closures inputs
• The contact closure device must be capable
of switching 12V--- at 4mA with a minimum contact
closure time of 0.25 seconds.
• Dual Group IR Remotes can control up to two
groups of Drives
• Drives can be assigned to different keypad groups
by rewiring
• Drives can be assigned to different IR transmitter
groups by reprogramming.
•
System Controls and Stanza
Integration
Stanza lighting control system keypads
communicate with drives via SZ-IO Stanza
contact closure output
• IR receivers must be wired directly to Drives
with IR connector (One IR receiver required per EDU)
• 2 Group IR transmitters provide wireless control
for two groups of shades or drapes
• Stanza Standalone shade keypads provide control
for up to two groups of drapes
•
Page 2
Stanza™
Standalone and Integrated System
System Specification
086-128 3 07.15.09
Stanza Standalone System
TM
| Single Drive Wiring
Wire Type A
1
2
3
Com
24 V--Close
Open
IR Receiver
Stanza Drapery or
Roller Shade Drive
4
5
6
7
8
9
Terminal block of
Drive controlling single
Shade or Drape
Single Group
Keypad
Com
X
Single group 1
IR Transmitter
24 V---
Wire Type B
SZ-PS-1-50
Power Supply
3
Notes:
• Standalone shade or drapery drives can be controlled with a keypad, IR remote, or both.
• Pressing any button on any keypad or IR remote while the shade or drape is moving will
cause the shades or drapes in the group to stop.
Wiring types
A
B
Job Name:
Job Number:
Purpose
Contact Closure input/output
Wire options
18-22 AWG (1.00-0.50 mm²)
per contact closure - 250 ft (75 m) max
Drive power (power supply to Drive) 12 AWG - (4 mm²)-250 ft (75 m) max
16 AWG - (1.5 mm²)-100 ft (30 m) max
Lutron P/N QSHY-CBL-M-1000 Non-plenum
Lutron P/N QSHY-CBLP-M-1000 plenum
18 AWG - (1 mm²)-50 ft (17 m) max
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 3
Stanza™
Standalone and Integrated System
System Specification
086-128 4 07.15.09
Stanza Standalone System | Dual Drive Wiring
Com
24 V---
X
TM
SZ-PS-1-50
Power Supply
Wire Type B
1
Optional IR
Receiver
Stanza Drapery or
Roller Shade Drive
Optional IR
Receiver
2
3
4
5
6
7
8
9
Terminal block of
Drive controlled by
Group 1 buttons
Wire Type A
Com
Com
24 V
V--24
Close
Close
Open
Open
1
2
Dual Group Keypad
Terminal block of
Drive controlled by
Group 2 buttons
Wire Type B
Com
24 V---
Stanza Drapery or
Roller Shade Drive
X
1
Com
Com
24 V
24
V--Close
Close
Open
Open
SZ-PS-1-50
Power Supply
Dual group
3
IR Transmitter
Notes:
• Standalone shade or drapery drives can be controlled with a keypad, IR remote, or both.
• Pressing any button on any keypad or IR remote while the shade or drape is moving will
cause the shades or drapes in the group to stop.
Wiring types
A
B
Job Name:
Job Number:
Purpose
Contact Closure input/output
Wire options
18-22 AWG (1.00-0.50 mm²)
per contact closure - 250 ft (75 m) max
Drive power (power supply to Drive) 12 AWG - (4 mm²)-250 ft (75 m) max
16 AWG - (1.5 mm²)-100 ft (30 m) max
Lutron P/N QSHY-CBL-M-1000 Non-plenum
Lutron P/N QSHY-CBLP-M-1000 plenum
18 AWG - (1 mm²)-50 ft (17 m) max
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 4
Stanza™
Standalone and Integrated System
System Specification
086-128 5 07.15.09
Stanza Integrated System | Single Drive Wiring
TM
Contact Closure Outputs (CCO)
CCO 1 NC
CCO 1 NO
1-2 COM
CCO 2 NC
CCO 2 NO
CCO 3 NC
CCO 3 NO
3-4 COM
CCO 4 NC
CCO 4 NO
CCO 5 NC
CCO 5 NO
5 COM
CCI 1
CCI 2
CCI 3
CCI 4
CCI 5
COM
+PWR
COM
Contact Closure Inputs (CCI)
SZ-IO
Contact Closure
Interface
Com
24 V--Close
Open
Com
24 V---
Wire Type B
X
Stanza Drapery or
Roller Shade Drive
Wire Type A
Terminal block of
Drive controlling
single Shade or
Drape
SZ-PS-1-50
Power Supply
Notes:
• SZ-IO outputs programmed as a 0.25 second momentary contact closure output
• Activating Open or Close while the shade or drape is moving will cause it to stop
• If a Stop function is required, program the SZ-IO to activate both Open and Close contacts
simultaneously (within 50 ms of each other)
Wiring types
A
B
Job Name:
Job Number:
Purpose
Contact Closure input/output
Wire options
18-22 AWG (1.00-0.50 mm²)
per contact closure - 250 ft (75 m) max
Drive power (power supply to Drive) 12 AWG - (4 mm²)-250 ft (75 m) max
16 AWG - (1.5 mm²)-100 ft (30 m) max
Lutron P/N QSHY-CBL-M-1000 Non-plenum
Lutron P/N QSHY-CBLP-M-1000 plenum
18 AWG - (1 mm²)-50 ft (17 m) max
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 5
Stanza™
Standalone and Integrated System
System Specification
086-128 6 07.15.09
Stanza Integrated System
TM
|
Dual Drive Wiring
Contact Closure Outputs (CCO)
SZ-PS-1-50
Power Supply
CCO 1 NC
CCO 1 NO
1-2 COM
CCO 2 NC
CCO 2 NO
CCO 3 NC
CCO 3 NO
3-4 COM
CCO 4 NC
CCO 4 NO
CCO 5 NC
CCO 5 NO
5 COM
CCI 1
CCI 2
CCI 3
CCI 4
CCI 5
COM
+PWR
COM
Com
24 V---
X
Contact Closure Inputs (CCI)
Wire Type B
SZ-IO
Com
24 V--Close
Open
Stanza Drapery or
Roller Shade Drive
Terminal block of
Drive controlling
sheer Shade or
Drape
Wire Type A
Com
24 V--Close
Open
Terminal block of
Drive controlling
blackout Shade
or Drape
Stanza Drapery
or Roller Shade
Drive
Com
24 V---
X
Wire Type B
SZ-PS-1-50
Power Supply
Notes:
• SZ-IO outputs programmed as a 0.25 second momentary contact closure output
• Activating Open or Close while the shade or drape is moving will cause it to stop
• If a Stop function is required, program the SZ-IO to activate both Open and Close contacts
simultaneously (within 50 ms of each other)
Wiring types
A
B
Job Name:
Job Number:
Purpose
Contact Closure input/output
Wire options
18-22 AWG (1.00-0.50 mm²)
per contact closure - 250 ft (75 m) max
Drive power (power supply to Drive) 12 AWG - (4 mm²)-250 ft (75 m) max
16 AWG - (1.5 mm²)-100 ft (30 m) max
Lutron P/N QSHY-CBL-M-1000 Non-plenum
Lutron P/N QSHY-CBLP-M-1000 plenum
18 AWG - (1 mm²)-50 ft (17 m) max
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 6
Stanza™
Standalone and Integrated System
System Specification
086-128 7 07.15.09
Stanza
TM
|
Contact Closure Input Wiring and Specification
Com
24 V--Close
Open
Stanza Drapery or
Roller Shade Drive
Terminal block of
Drive controlling single
Shade or Drape
Wire Type A
Wire Type B
Com
24 V---
X
1
SZ-PS-1-50
Power Supply
3
Notes:
• The Stanza Drive accepts Class 2, dry contact closure inputs. The contact closure device
must be capable of switching 12 V--- at 4 mA. Momentary dry contact closure inputs require
a minimum closure time of 0.25 seconds.
• Activating Open or Close while the shade or drape is moving will cause it to stop
• A dedicated Stop function can be actuated one of the following two ways:
1. Activate both Open and Close contacts simultaneously (within 50 ms of each other)
2. Providing a Stop contact closure with the following circuit:
Com
24 V--Open
Close
Close
D1
D2
Stop
Open
Diodes D1 and D2 must be rated for 12 V ---, 4 mA
Wiring types
A
B
Job Name:
Job Number:
Purpose
Contact Closure input/output
Wire options
18-22 AWG (1.00-0.50 mm²)
per contact closure - 250 ft (75 m) max
Drive power (power supply to Drive) 12 AWG - (4 mm²)-250 ft (75 m) max
16 AWG - (1.5 mm²)-100 ft (30 m) max
Lutron P/N QSHY-CBL-M-1000 Non-plenum
Lutron P/N QSHY-CBLP-M-1000 plenum
18 AWG - (1 mm²)-50 ft (17 m) max
S p e c i f i c at i o n S u b m i t ta l
Model Numbers:
Page 7